Easley, SC – HVAC Services

Arrived for a no cooling call. Found that the blower would come on but outdoor unit would not. Checked the dissipation board and it was giving a refrigerant leak code. We recovered the refrigerant and repressurized with nitrogen up to 300psi and let it hold for 15 minutes. Removed nitrogen and pulled vacuum to 330 microns to verify no leaks. Recharged system to sub cool. Will need to return to replace faulty dissipation board and sensor under warranty. Verified operation in cooling mode. System is operational at time of departure.

Replaced 3 ton gas package unit. Replaced disconnect, whip, pad, and thermostat. Rebuilt flashing and sealed it with silicone. Verified operation in cooling mode. System is operational at time of departure.

Replaced 3-ton ac, coil, and 80% furnace. Replaced pad, disconnect, whip, 2 thermostats, pan. Reconnected system to existing zone system. Installed 2 float switches. Verified operation in cooling mode. System is operational at time of departure.

Search protection to outdoor and indoor unit as well as Mini Split for the bonus room(Mini Split surge protection installed in panel. Outdoor unit search protection install installed on unit.)

Installation of 16 SEER 4-Ton Side Discharge. Replaced drain pan, thermostat, disconnect, whip, and installed a surge protector. Installed 16x25x4 aprilaire cabinet. Verified operation in cooling mode. System is operational at time of departure.

There was a series of things going on here from the breaker to powering the unit. The breaker ended up being OK but after voltage was applied, I found that the contactor and battery cap was damaged. Battery cap was swollen and dead, and the contactor was charged and burnt. I replaced these per the homeowner. Paid with Visa.

High Efficiency-16 SEER Side discharge (Trane/Ingersol Rand) Ameristar Need to return to perform duct cleaning as it was very late when the job was completed.

Replaced 10 ton gas package unit with 5 ton gas package unit on roof. Utilized crane. Repositioned unit to reconnect into existing ductwork. Built stand for disconnect. Sealed original curb to prevent rain from leaking into building. Replaced thermostat. Verified operation in cooling mode. System is operational at time of departure.

Removal and disposal of existing gas Package Unit requiring removal of gas line, power and flashing from side of the house.

Customer has sold house. Drier duct cleaning brush stick in duct. Customer prefers to be called in visited in afternoon after 3 pm- Richard. Arrived 4/22/26 to see about getting dryer vent cleaning sticks out of a dryer vent another technician did. I put my camera on ground level into the dryer vent and couldn’t see anything. I called the technician and asked how many sticks did he lose and he told me three. I called Justin and install is scheduled for Friday morning to see if they can take the dryer vent apart in the attic to remove the sticks.- Walker. Take a dryer flex with you to connect between dryer and wall. Thomas and Sean returned on 4/27 No one would come to the door and have not been able to contact.

***Removal of old ductwork and old gas, furnace, and Installation of 2.5 ton AC/90% gas 3pc and full cut duct design. -14.3 seer AC (outdoor unit) -pad -power whip -disconnect -90% Gas furnace (crawlspace) w/transition and venting -April Aire (advanced filtration cabinet) -2.5 ton full cut duct design -no thermostat needed -10 year parts warranty -2 your labor warranty -5-year maintenance membership -12-inch booster fan (if necessary) -condensate pump 16,674

Replaced 2.5 ton heat pump air handler. Replaced whip, disconnect, pad, drain pan, and thermostat. Installed 20x20x4 Aprilaire filter and removed 1" filter from filter rack. Installed 2 drain safety float switches. Verified system in cooling. System is operational at time of departure.

Approximately 10 foot to be removed from the suction line and liquid line. Mindset to be braised together no need for. Any material

Customer has a mini split with 3 heads, two linesets are ran along the side of the house and one linset is ran under the house. The suspected damaged lineset is the one under the house. The hose is on a slope, and it gets very narrow where the lineset runs. Customer is fine with someone coming out tomorrow afternoon 2-4 to look at. Will speak with Kelsey on rescheduling this.

Installation of new 35/5 microphone capacitor due to the capacitor being 14 points low on herM. Indoor unit is on the third floor in the attic.

Replaced 2.5 ton heat pump and air handler. Replaced pad, whip, disconnect, thermostat. Had to replace return plenum bc it was rusted through on the bottom. Verified operation in heating mode. System is operational at time of departure.

Labor and contactor, as well as repaired to the wire that was rubbing copper on the inside of the condenser. This was due to a factory installation, failure with vibration, rubbing through the wire and chattering the contactor, dropping the signal to the outdoor unit, then trying again after the delay in the board. This would’ve been continuing to happen until repaired.

For this job I worked on troubleshooting back net errors. Upon inspection I discovered two dead capacitors and a gas leak. Called for approval and fixed gas leak and replaced capacitor ma. Pictures uploaded to documents.

Apon troubleshooting the issue where partial upstairs supply vents were moving forceful air into the room in excess I found that it was happening due to motor being burned out on one of the zone dampers. I did find that the system is failing and burning up motors due to the design of the ductwork and it being undersized in areas and oversized in others, making it impossible to carry the conditioned air/CFM that the duct design should be allowing from the system for each room. Ductwork was improperly designed and highly inefficient due to it originally being one Duct design that was pretty much cut in half and poorly made into two separate zones to give upstairs and downstairs function with their own thermostat. Normally, this would properly allow control of upstairs conditioning as well as downstairs conditioning from one system by zoning it and the one system allowing proper manual D for upstairs and downstairs load calculation. Each zone requires its own separate duct design/configur

Installation UV lights inside of the air handler between the blower housing and coil. Installed safety switches on the secondary drain line and chained in to the other two switches on the auxiliary drain pan and ez trap

Arrived today to perform tune up, checked electric heat, gas valve pressure, flame sensor, ignitor, inducer fan motor, watched sequence of operation, heat is working with no issues on both systems. checked for gas leak didn't find it. everything was working fine except for the ductwork for the system that is located in the attic couple boots was off the sheetrock and not insulated told him that's the reason why there is water around the supply.

Arrived on site to provide a quote for multi-head mini split. Customer did not want to move forward at this time.

Arrived for tune up found some issues on the system. battery cap contactor, also told them its time to add an easy start and a surge protector. Pressures are low. Gave the customer some options.

August 13th 2025 returned to top off the system that was low on our last visit customer stated that the system isn't doing what it was doing where it went into heat mode I believe the thermostat may have went into a test mode during that time. Topped off the refrigerant with R32 about a half a pound. Performed a leak search no leaks at the indoor coil for the line set that is accessible. No leak in the outdoor condenser coil or the line set that is accessible on the outdoor system. I did pick up a leak on our straighter valve. This could have been during installation not tightening it enough or during startup when we disconnect our hoses sometimes our gauge hoses or probe ends will grab the Schrader valve and slightly Twisted when we are disconnecting. I tighten down the straighter valve checked again and the leak was no longer present. Customer mentions wanting to do her fall maintenance and the month of October if possible. She mentioned she may call Kelsey but just in case I'm putt

Arrived today for an estimate but customer just wanted the system to be checked out. I told the owner it will be $39. She agreed. Checked pressures and they were fine. Customer joined us. She paid the 99.00 today.