Anderson SC – HVAC Services

Performed duct cleaning on 11 supply vents and 2 return vents.

Replaced 3 ton heat pump air handler. Replaced pad, disconnect, whip, zone board, 2 thermostats. Installed 2 float switches. Installed DAT sensor. Installed 12" bypass damper. Verified operation in cooling mode. System is operational at time of departure.

Installation of new 3 Ton straight AC/gas three-piece split system in the crawlspace with advanced filtration

Installation of 1 ton mini split outdoor heat pump 1 ton mini split evaporator coil head indoors Pad Power whip Disconnect 12 yr parts warranty Five year maintenance membership Ran new line set with line hide. Replaced single pole 30 amp breaker with double pole 15amp breaker. Installed new pad, disconnect, and whip. Verified operation in cooling. System is operational at time of departure.

Removed and replaced 4 ton duct system. Upsized 2 trunk lines and installed a bypass damper. Replaced plenum and DAT sensor. Replaced 3 zone dampers. Verified operation in cooling mode. System is operational at time of departure.

Water heater was turned off.

Replaced 2 ton gas package unit with new pad, disconnect, whip, and thermostat. Verified operation in heating and cooling mode. System is operational at time of departure.

Replaced 2 ton heat pump and air handler. Ran new line set and replaced disconnect, whip, pad, and wifi thermostat. Replaced breakers to the correct size. System is operational at time of departure.

Installation of new 2 ton heat pump/air handler split system in Crawlspace w/ “full cut” ductwork -Seven supplies with boots and 4x10” vents… 14 x 20 return floor drill or “stack head/dropbox” Need to return after electrical panel has been upgraded to perform start up.

Installation of new ECM blower motor covered under warranty

4 ton ,16 seer side discharge heat pump(conventional wiring) Air handler Side discharge pad Power whip Disconnect April air advanced filtration Standard zone board Two Wi-Fi thermostats

Installation of communicating zone panel. cst has not paid yet the board is discontinued from what trane and the other supply houses are telling us. cst asked us the come back 2-26-26 in the morning when wife will be home to go over options.

Dryer vent cleaning and customer was adamant that that’s all they wanted to pay for and would not let me look at the equipment. Customer has McGee heating in there, but they only have one more maintenance and they are going to consider us because the relationship was definitely established and their equipment is coming up on 10 years so I’ve planted the seed that it’s possible we can do a buyback to give them a new 10 year warranty on new equipment, which gives them an opportunity of a warranty that is gonna last longer than their equipment is now. The relationship is quite established though.

This is a brand-new apartment duplex. Customer didn’t know what was going on and why the thermostat was blank, but I did find that the breaker was off, but the breaker was off because the system is actually not cutting off when it is satisfied or if you just turn it off. I did find that this particular blower control relay is inside of the ECM itself and will require replacement of the ECM motor. It is very unfortunate that the blower relay is not external. It is recommended with the parts number. I have up to replace the small relay with the chip at the same time as replacing the blower motor, but all that can be done within the pricing of the installation of the new ECM motor. Motor is definitely under warranty. I did tell the owner that I would price surge protection.

This is a Coleman gas pack on the left-hand side of the Home; picture of modeling serial number uploaded to documents. All orders of operation for startup are within factory specs but when it comes to the blower, kicking on after the exchanger is hot or the timed delay sends the signal to the blower it is doing so but the blower is failing to stay running with applied voltage. The motor is taking on proper voltage from high and low but not holding the command and failing itself. ECM blower motor will need to be replaced. I quoted the homeowner $490 to replace the ECM motor that is still under warranty. Please note that the homeowner is going to go ahead and pay for Maintenance when we come out and wants to see if her first Maintenance, which would be the fall Maintenance can be done the same day of the blower motor install. Motor has been ordered from Johnstone. The old motor is available for the swap on the warranty. Can be put on schedule for Thursday afternoon. Motor is being order

This will be installation of the zone board and two thermostats that will be supplied by a 70 V transformer, labor, in the price.

System has caught a surge and smoked thermostats and zone board We will need to replace the zone board and two thermostats as well as rewire on the outdoor unit and indoor unit coming from outdoor outdoors. System will also need a 70 V transformer due to two thermostats, two boards, a zone board, and three motors running off of 1-40 V. Transformer. I will pick the things up from Ferguson for Monday. I was able to bypass and get emergency strip heat only with both zones open for a temporary solution until Monday when we come back.

Customer went with different company.

Codes are cleared and a normal operation. Standby.

April air to be installed on the return Plenum. Return Plenum is located on the right side of the system with three return attachments. This will go between the Plenum and the system.

Tune up- checked all heating and cooling aspects of system, notating with the customer the biggest concern is changing out the condenser fan motor “pitted and rust” indicating overheating and cleaning off the blower wheel. Customer understands the work that the system needs and will reach out.

Total system restoration - checked pressures and electrical. Found leak in system due to refrigerant levels low. Customer decided not to do anything at this time.

Installed 2ton heat pump with two new disconnects indoor and outdoor with pad whip and thermostat. Installed new condensate pump and verified drainage. New copper line set was also installed with the units. Installed new ducting system with 7 runs new supplies and return plenum new trunk lines and return duct. Homeowner was educated on thermostat.

Customer was interested at this time in price only no commitments at this time. Has a 2.5 Ton HP / AH. Justin gave me the price of 9987.

Arrived at customers home and customer explained her system is 19 years old and she is interested in a new one. The system is a R22 that has an extremely low superheat. Compressor and fan motor extremely hot. Condenser is unlevel. Furnace drain pans full of water, evaporator coil frozen and blower is off balance. This information was brought to the attention of the customer. Ran credit for new system 10987. BC. Customer will speak with her father, and I will follow up of Tuesday. Customer was made aware of issues with the drain pan full of water and any and all other issues.